Help setting up a Sangoma 102a

kevwyo · April 27, 2010, 7:13pm

I am trying to get my Sangoma card to register on my freepbx. I have followed the steps for installing zaptel and dahdi and wanpipes.
wgets and rpms were
zaptel-1.4.12.1
wanpipes-3.4.9
dahdi-linux-complete-2.3.0+2.3.0
freepbx-2.5.1

first let me setup the system a little. I have a sip trunk that is working and incoming and outbound calls work fine. my cdr is not functioning as the report option on web interface say no data found. but I figured I messed something up thereand will work on that later. currently I have spent the last week trying to get my analog phone lines to work.
I have a Sangoma 102 2 port t1 with a single t1 cable from my Rhino cb-24 to the a port of my sangoma. I can look on the front of the cb-24 and see zeros all the way across the rx line and 8 l’s across the tx line. (except for the B were I have one test phone line plugged in) I can dial the number and watch the rhino lite up but some how I am missing some piece of knowledge on linking my card to freepbx. when I run wanrouter status I get
Devices currently active:
wanpipe1

Wanpipe Config:

Device name | Protocol Map | Adapter | IRQ | Slot/IO | If’s | CLK | Baud rate |
wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 185 | 4 | 0 | N/A | 0 |

Wanrouter Status:

dahdi_genconf
Empty configuration – no spans
Empty configuration – no spans

I have set my zap trunk to
trunk description = sangoma
any cid allowed
911 dial plan
zap identifier = w1g1 (tried e164, wanpipe1, g0)

so far the system will not pick up the calls. my main outbound dial plan is to use the sip trunk which is working and use this for analog inbound and 911 calls. I am really at a loss as to what I am missing. I know it is going to be something small. I have ran through the setup-sangoma and wancfg_dahdi which both seem to setup the sangoma. I take options

t1
normal
10-fxo kewl start (my rhino says fxo loop on screen) I have tried fxo loop and ground as well as fxs loop,ground,kewl
defaults on rest of items from-internal (tried from-pstn)

thanks

kevwyo · May 19, 2010, 3:35pm

I have since updated to wanpipe 3.5.11 did all the make’s again and then with the dahdi-linux-complete-2.3.0+2.3.0 and all the make’s and I now have my zap/dahdi channel set to g0 and my 8 ports (pots) show up in the web panel. but my incoming calls are never connected. they are recieved and it starts the IVR but the calling phone continues to ring. even when they hang up it still runs through the system and rings a group but when they pick up no one is there. all you here is clicks and clicks. when I look at the Rhino cb-24 my rx1-8 has solid 8’s or B’s but the tx1-8 has blinking 8’s in the pots lines. when you recieve a call the rx goes to a solid 1 on that channel but the tx flashes 8 0 1 real quick and never gets off that. I have tried increasing the tx gain in zapata.conf and chan_dahdi.conf then restarting with
amportal stop
wanrouter restart
amportal start
but it does not change. is there a different place I should be increasing my tx gain? or is it my tx gain I should be worried about?

thanks

kevwyo · May 19, 2010, 7:08pm

here is a incoming call on the system. which progresses along great but the connection is never established. the caller is still ringing while all this is going on. when we pick up the phone there is nothing there but clicks. and the caller has long since hung up. I do not know if I mentioned it but I have a sangoma a102 card in my server and it is attached to a Rhino CB-24 via T1 cable. when I mention watching the Rhino I can see the action on the Rhino screen but it is like the caller is never sent a off-hook command.

[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:1] Set(“DAHDI/7-1”, “LOOPCOUNT=2”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:2] GotoIf(“DAHDI/7-1”, “0?s|begin”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:3] DBdel(“DAHDI/7-1”, “”) in new stack
[May 19 12:57:57] WARNING[9753] app_db.c: The DBdel application has been deprecated in favor of the DB_DELETE dialplan function!
[May 19 12:57:57] DEBUG[9753] app_db.c: Ignoring, no parameters
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:4] Set(“DAHDI/7-1”, “__NODEST=”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:5] Goto(“DAHDI/7-1”, “timeconditions|1|1”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (timeconditions,1,1)
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:1] GotoIfTime(“DAHDI/7-1”, “08:00-17:00|mon-fri||?ext-group|600|1”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (ext-group,600,1)
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:1] Macro(“DAHDI/7-1”, “user-callerid|”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:1] Set(“DAHDI/7-1”, “AMPUSER=”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:2] GotoIf(“DAHDI/7-1”, “0?report”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:3] ExecIf(“DAHDI/7-1”, “1|Set|REALCALLERIDNUM=”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: ExecIf
[May 19 12:57:57] DEBUG[9753] app_macro.c: Last app: Set|REALCALLERIDNUM=
[May 19 12:57:57] DEBUG[9753] func_db.c: DB: DEVICE//user not found in database.
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:4] Set(“DAHDI/7-1”, “AMPUSER=”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] DEBUG[9753] func_db.c: DB: AMPUSER//cidname not found in database.
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:5] Set(“DAHDI/7-1”, “AMPUSERCIDNAME=”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:6] GotoIf(“DAHDI/7-1”, “1?report”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-user-callerid,s,10)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:10] GotoIf(“DAHDI/7-1”, “0?continue”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:11] Set(“DAHDI/7-1”, “__TTL=64”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:12] GotoIf(“DAHDI/7-1”, “1?continue”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-user-callerid,s,19)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:19] NoOp(“DAHDI/7-1”, “Using CallerID “” <>”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Noop
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:2] GotoIf(“DAHDI/7-1”, “1?skipdb”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (ext-group,600,4)
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:4] Set(“DAHDI/7-1”, “__NODEST=”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:5] Set(“DAHDI/7-1”, “__BLKVM_OVERRIDE=BLKVM/600/DAHDI/7-1”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:6] Set(“DAHDI/7-1”, “__BLKVM_BASE=600”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:7] Set(“DAHDI/7-1”, “DB(BLKVM/600/DAHDI/7-1)=TRUE”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:8] Set(“DAHDI/7-1”, “RRNODEST=”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:9] Set(“DAHDI/7-1”, “__NODEST=600”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:10] GosubIf(“DAHDI/7-1”, “0?sub-rgsetcid|s|1”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:11] Set(“DAHDI/7-1”, “RecordMethod=Group”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:12] Macro(“DAHDI/7-1”, “record-enable|7000-7003-7005-7007|Group”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]nable:1] GotoIf(“DAHDI/7-1”, “1?check”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,4)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:4] ExecIf(“DAHDI/7-1”, “0|MacroExit|”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: ExecIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:5] GotoIf(“DAHDI/7-1”, “1?Group:OUT”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,6)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:6] Set(“DAHDI/7-1”, “LOOPCNT=4”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:7] Set(“DAHDI/7-1”, “ITER=1”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:8] GotoIf(“DAHDI/7-1”, “1?continue”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,13)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:13] Set(“DAHDI/7-1”, “ITER=2”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:14] GotoIf(“DAHDI/7-1”, “1?begin”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,8)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:8] GotoIf(“DAHDI/7-1”, “1?continue”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,13)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:13] Set(“DAHDI/7-1”, “ITER=3”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:14] GotoIf(“DAHDI/7-1”, “1?begin”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,8)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:8] GotoIf(“DAHDI/7-1”, “1?continue”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,13)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:13] Set(“DAHDI/7-1”, “ITER=4”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:14] GotoIf(“DAHDI/7-1”, “1?begin”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,8)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:8] GotoIf(“DAHDI/7-1”, “1?continue”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Goto (macro-record-enable,s,13)
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:13] Set(“DAHDI/7-1”, “ITER=5”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:14] GotoIf(“DAHDI/7-1”, “0?begin”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:15] GotoIf(“DAHDI/7-1”, “0?IN”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] DEBUG[9753] func_db.c: DB: AMPUSER/7000-7003-7005-7007/recording not found in database.
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:16] ExecIf(“DAHDI/7-1”, “1|MacroExit|”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:13] Set(“DAHDI/7-1”, “RingGroupMethod=ringall”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:14] Macro(“DAHDI/7-1”, “dial|20|tr|7000-7003-7005-7007”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:1] GotoIf(“DAHDI/7-1”, “0?dial”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: GotoIf
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:2] SetMusicOnHold(“DAHDI/7-1”, “moh”) in new stack
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: SetMusicOnHold
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:3] AGI(“DAHDI/7-1”, “dialparties.agi”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Launched AGI Script /var/lib/asterisk/agi-bin/dialparties.agi
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: Starting New Dialparties.agi
[May 19 12:57:57] VERBOSE[9816] logger.c: == Parsing ‘/etc/asterisk/manager.conf’: [May 19 12:57:57] VERBOSE[9816] logger.c: Found
[May 19 12:57:57] VERBOSE[9816] logger.c: == Parsing ‘/etc/asterisk/manager_additional.conf’: [May 19 12:57:57] VERBOSE[9816] logger.c: Found
[May 19 12:57:57] VERBOSE[9816] logger.c: == Parsing ‘/etc/asterisk/manager_custom.conf’: [May 19 12:57:57] VERBOSE[9816] logger.c: Found
[May 19 12:57:57] VERBOSE[9816] logger.c: == Manager ‘admin’ logged on from 127.0.0.1
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: Caller ID name is ‘unknown’ number is ‘unknown’
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: USE_CONFIRMATION: ‘FALSE’
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: RINGGROUP_INDEX: ‘’
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: Methodology of ring is ‘ringall’
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Added extension 7000 to extension map
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Added extension 7003 to extension map
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Added extension 7005 to extension map
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Added extension 7007 to extension map
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7000 cf is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7003 cf is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7005 cf is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7007 cf is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7000 do not disturb is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7003 do not disturb is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7005 do not disturb is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Extension 7007 do not disturb is disabled
[May 19 12:57:57] VERBOSE[9753] logger.c: > dialparties.agi: extnum 7000 has: cw: 0; hascfb: 0 [] hascfu: 0 []
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: Extension 7000 has ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Checking CW and CFB status for extension 7000
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: DbDel CALLTRACE/7000 - Caller ID is not defined
[May 19 12:57:57] VERBOSE[9753] logger.c: > dialparties.agi: extnum 7003 has: cw: 0; hascfb: 0 [] hascfu: 0 []
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: Extension 7003 has ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Checking CW and CFB status for extension 7003
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: DbDel CALLTRACE/7003 - Caller ID is not defined
[May 19 12:57:57] VERBOSE[9753] logger.c: > dialparties.agi: extnum 7005 has: cw: 0; hascfb: 0 [] hascfu: 0 []
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: Extension 7005 has ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Checking CW and CFB status for extension 7005
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: DbDel CALLTRACE/7005 - Caller ID is not defined
[May 19 12:57:57] VERBOSE[9753] logger.c: > dialparties.agi: extnum 7007 has: cw: 0; hascfb: 0 [] hascfu: 0 []
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: dialparties.agi: Extension 7007 has ExtensionState: 0
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Checking CW and CFB status for extension 7007
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: DbDel CALLTRACE/7007 - Caller ID is not defined
[May 19 12:57:57] VERBOSE[9753] logger.c: – dialparties.agi: Filtered ARG3: 7000-7003-7005-7007
[May 19 12:57:57] VERBOSE[9753] logger.c: > dialparties.agi: NODEST: 600 adding M(auto-blkvm) to dialopts: trM(auto-blkvm)
[May 19 12:57:57] VERBOSE[9753] logger.c: > dialparties.agi: NODEST: 600 blkvm enabled macro already in dialopts: trM(auto-blkvm)
[May 19 12:57:57] VERBOSE[9816] logger.c: == Manager ‘admin’ logged off from 127.0.0.1
[May 19 12:57:57] VERBOSE[9753] logger.c: – AGI Script dialparties.agi completed, returning 0
[May 19 12:57:57] DEBUG[9753] app_macro.c: Executed application: AGI
[May 19 12:57:57] VERBOSE[9753] logger.c: – Executing [[email protected]:7] Dial(“DAHDI/7-1”, “SIP/7000&SIP/7003&SIP/7005&SIP/7007|20|trM(auto-blkvm)”) in new stack
[May 19 12:57:57] VERBOSE[9753] logger.c: – Called 7000
[May 19 12:57:57] VERBOSE[9753] logger.c: – Called 7003
[May 19 12:57:57] VERBOSE[9753] logger.c: – Called 7005
[May 19 12:57:57] VERBOSE[9753] logger.c: – Called 7007
[May 19 12:57:57] VERBOSE[9753] logger.c: – SIP/7007-00000005 is ringing
[May 19 12:57:57] VERBOSE[9753] logger.c: – SIP/7000-00000002 is ringing
[May 19 12:57:57] VERBOSE[9753] logger.c: – SIP/7003-00000003 is ringing
[May 19 12:57:57] VERBOSE[9753] logger.c: – SIP/7005-00000004 is ringing
[May 19 12:57:59] VERBOSE[9753] logger.c: – SIP/7003-00000003 answered DAHDI/7-1
[May 19 12:57:59] VERBOSE[9753] logger.c: – Executing [[email protected]:1] Set(“SIP/7003-00000003”, “__MACRO_RESULT=”) in new stack
[May 19 12:57:59] DEBUG[9753] app_macro.c: Executed application: Set
[May 19 12:57:59] VERBOSE[9753] logger.c: – Executing [[email protected]:2] DBdel(“SIP/7003-00000003”, “BLKVM/600/DAHDI/7-1”) in new stack
[May 19 12:57:59] VERBOSE[9753] logger.c: – DBdel: family=BLKVM, key=600/DAHDI/7-1
[May 19 12:57:59] DEBUG[9753] app_macro.c: Executed application: dbDel
[May 19 12:57:59] DEBUG[9753] app_dial.c: Macro exited with status 0

kevwyo · June 10, 2010, 4:11pm

ok I had sangoma and rhino helping me with this and we ran every test under the book. even had phone company check signal levels and all was perfect. problem was solved with a simple unplug the db25 cable from the rhino to the pots jacks clean and re-plug in. everything works great DUH… can not tell you how much I learned about everything else just to find a cable dirty/loose anyway works great now.

system · June 4, 2014, 7:00pm