DAHDI AEX800 - Debian 12

Commercial Products and Partners Sangoma
1

Hi there!

I’ve trying install Digium AEX 800 on Debian 12, but with unsuccessful.

Here are some outputs:

lspci -vvv

02:08.0 Ethernet controller: Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express) (rev 11)
Subsystem: Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
IOMMU group: 9
Region 0: I/O ports at e000 [disabled] [size=256]
Region 1: Memory at f7120000 (32-bit, non-prefetchable) [disabled] [size=1K]
Expansion ROM at f7100000 [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

@pbx01:~# dahdi_hardware
pci:0000:02:08.0 wctdm24xxp- d161:8002 Wildcard AEX800

@pbx01:~# lsmod | egrep dah
dahdi_voicebus 77824 1 wctdm24xxp
dahdi 258048 4 wctdm24xxp,dahdi_voicebus,oct612x,wcaxx

@pbx01:~# dahdi_genconf -vvvv
Default parameters from /etc/dahdi/genconf_parameters
Empty configuration – no spans
Generating /etc/dahdi/assigned-spans.conf
Empty configuration – no spans
Generating /etc/dahdi/system.conf
Empty configuration – no spans
Generating /etc/asterisk/dahdi-channels.conf

@pbx01:~# dahdi_cfg -vvvvv
DAHDI Tools Version - 3.1.0

DAHDI Version: 3.4.0
Echo Canceller(s):
Configuration

Channel map:

0 channels to configure.

===========================

Can someone give me some tip ou help me?

Thank you!!!

2

Howdy and welcome to the forums!

Have you gotten that same card to work recently in any earlier system ?

What happens if you plug in a phone line to one of the ports ?

3

Hi there!

First of all, i’m going answer your questions and after comment the solution. ****This contribuition was pending from me. :))

Have you gotten that same card to work recently in any earlier system ?
-Yes, i had it ok on FreePBX 16/Centos 7.

What happens if you plug in a phone line to one of the ports ?
-Nothing

I thought that problem was related with driver. I was right.

Searging, I got the PhreakScript from InterLinked (GitHub - InterLinked1/phreakscript: A utility to automate the installation, maintenance, and debugging of Asterisk/DAHDI, while integrating additional patches to provide the richest telephony experience) that has an option to get the dahdi driver and apply patch to restore the purge done at 2018 by Sangoma.
“Restores the “great purge” of DAHDI drivers that were removed in 2018 by Sangoma”

Executing this dahdi instalation with the above option, i’m sucefull using AEX800 on Debian 12.

Credits for InterLinked.

Thanks Penguinpbx!!

4

This topic was automatically closed 31 days after the last reply. New replies are no longer allowed.