Trixbox and two sip trunks?

hi, i try to setup 2 sip trunks for local network (just for test in my home) but i dont know what i need to do.
i have status like this:
Active Channel(s)

Peer User/ANR Call ID Format Hold Last Message
192.168.3.30 9995 2e23fc3c1b18026 0x0 (nothing) No Rx: REGISTER
192.168.3.30 9996 60a7b11d2291bcd 0x0 (nothing) No Rx: REGISTER
2 active SIP dialogs

Sip Registry

Host Username Refresh State Reg.Time
192.168.3.30:5060 9996 105 Registered Mon, 14 Oct 2013 12:34:06
192.168.3.30:5060 9995 105 Registered Mon, 14 Oct 2013 12:34:06
2 SIP registrations.

Sip Peers

Name/username Host Dyn Nat ACL Port Status
9996/9996 192.168.3.30 D 5060 OK (1 ms)
9995/9995 192.168.3.30 D 5060 OK (1 ms)
2 sip peers [Monitored: 2 online, 0 offline Unmonitored: 0 online, 0 offline]

when i try call from one PC (x-lite 9996) to other PC (x-lite 9995) trixbox server give me:

-- Executing [9996@from-sip-external:1] NoOp("SIP/trixbox1.localdomain-0000018e", "Received incoming SIP connection from unknown peer to 9996") in new stack
-- Executing [9996@from-sip-external:2] Set("SIP/trixbox1.localdomain-0000018e", "DID=9996") in new stack
-- Executing [9996@from-sip-external:3] Goto("SIP/trixbox1.localdomain-0000018e", "s,1") in new stack
-- Goto (from-sip-external,s,1)
-- Executing [s@from-sip-external:1] GotoIf("SIP/trixbox1.localdomain-0000018e", "1?from-trunk,9996,1") in new stack
-- Goto (from-trunk,9996,1)
-- Executing [9996@from-trunk:1] Set("SIP/trixbox1.localdomain-0000018e", "__FROM_DID=9996") in new stack
-- Executing [9996@from-trunk:2] NoOp("SIP/trixbox1.localdomain-0000018e", "Received an unknown call with DID set to 9996") in new stack
-- Executing [9996@from-trunk:3] Goto("SIP/trixbox1.localdomain-0000018e", "s,a2") in new stack
-- Goto (from-trunk,s,2)
-- Executing [s@from-trunk:2] Answer("SIP/trixbox1.localdomain-0000018e", "") in new stack
-- Executing [s@from-trunk:3] Wait("SIP/trixbox1.localdomain-0000018e", "2") in new stack
-- Executing [s@from-trunk:4] Playback("SIP/trixbox1.localdomain-0000018e", "ss-noservice") in new stack
-- <SIP/trixbox1.localdomain-0000018e> Playing 'ss-noservice.gsm' (language 'en')
-- Executing [s@from-trunk:5] SayAlpha("SIP/trixbox1.localdomain-0000018e", "9996") in new stack
-- <SIP/trixbox1.localdomain-0000018e> Playing 'digits/9.gsm' (language 'en')
-- <SIP/trixbox1.localdomain-0000018e> Playing 'digits/9.gsm' (language 'en')
-- <SIP/trixbox1.localdomain-0000018e> Playing 'digits/9.gsm' (language 'en')
-- <SIP/trixbox1.localdomain-0000018e> Playing 'digits/6.gsm' (language 'en')
-- Executing [s@from-trunk:6] Hangup("SIP/trixbox1.localdomain-0000018e", "") in new stack

== Spawn extension (from-trunk, s, 6) exited non-zero on ‘SIP/trixbox1.localdomain-0000018e’
– Executing [h@from-trunk:1] Hangup(“SIP/trixbox1.localdomain-0000018e”, “”) in new stack
== Spawn extension (from-trunk, h, 1) exited non-zero on ‘SIP/trixbox1.localdomain-0000018e’

i know, i need setup INBOUND ROUTES and OUTBOUND ROUTES, but i dont know how. I`m sure can somebody explain me.

Thanks a lot

trixbox has been abandoned for over 2 years. Suggest you download the latest FreePBX distro then go to our wiki and read the getting started guide.

If you are only running on your LAN what are these trunks going to connect to?

hi again, i download FreePBX but i cant take sip registration now. I try all my settings from TrixBOX but FreePBX make me trouble. In section “Settings > Asterisk SIP Settings” NAT it’s not possible setup “AUTO”. When i try edit file “sip.conf” there is noting from “Aseterisk SIP Settings”, but when i add any lines under [GENERAL] then FreePBX show me error at “Aseterisk SIP Settings”.
to everyone can someone explain me how to setup FreePBX???

My network looking like that:

MODEM<<< ------- >>>hub<<<–±----->>>FREEPBX<<<
192.168.3.1 | 192.168.3.30
|
----->>> pc1 <<<
| 192.168.3.2
|
----->>> pc2 <<<
| 192.168.3.3
|
----->>> printer <<<
192.168.3.20