Raspbx Freepbx gsm Gateway Detailed Tutorial needed

i am new to freepbx i intend to buy Goip GSM Gateway then i saw Raspbx Chan Dongle GSM Gateway
so i bought all meterials and almost build halfway and now i am stuck unknowing the FreePBX setup

so far incoming and forwading SMS(http://raspbx/sms/) only works
Raspbx Asterisk (Ver. 11.8.0)

inbound Routes name : inbond

  1. inbond Set Destination : Extensions <200> 200-ext
  2. Goog motif Set Destination : Extensions <200> 200-ext

outbond Route name : out_GSM

Trunk Sequence for Matched Routes 0 : Dongle (Unlocked E303s-1)
Dial Patterns that will use this Route : NXXNXXXXXX & NXXXXXX
Optional Destination on Congestion : Normal Congestion

Trunks Name : Dongle
Maximum Channels : 1
Custom Dial String : dongle/dongle0/$OUTNUM$

i did spend a lot of time on
http://www.freepbx.org/forum
http://nerdvittles.com/
http://www.raspberry-asterisk.org/ does not give me any clue
http://sourceforge.net/projects/raspbx/

aybody give me better detailed setup for Raspbx GSM Gateway

Thank you

Did you catch this page?

http://www.raspberry-asterisk.org/documentation/gsm-voip-gateway-with-chan_dongle/

It’s about as detailed as you can get.

yes i did follow everything on that page

tried youtube aswell no luck so far almost 2 weeks of search for help find no detaild answer

Did you read this?

http://wiki.e1550.mobi/doku.php?id=usage

Don’t forget when reading this all the configs are done by the install-dongle script (in theory anyway).
Does Asterisk see your dongle?

What is the output of:

dongle show devices
and

dongle show device xxx where xxx is the device name from previous step?

When you built custom trunk did you do dial string exactly as shown?

raspbx*CLI> dongle show device state dongle0
-------------- Status -------------
Device : dongle0
State : Free
Audio : /dev/ttyUSB1
Data : /dev/ttyUSB2
Voice : Yes
SMS : Yes
Manufacturer : huawei
Model : E303S
Firmware : 21.157.31.00.850
IMEI : 86XXXXXXXXXXXX
IMSI : 31XXXXXXXXXXXX
GSM Registration Status : Registered, roaming
RSSI : 25, -63 dBm
Mode : GSM/GPRS
Submode : EDGE
Provider Name : T-Mobile
Location area code : "XXXX"
Cell ID : "XXXX"
Subscriber Number : +1XXXXXXXXXX
SMS Service Center : +1XXXXXXXXXX
Use UCS-2 encoding : Yes
USSD use 7 bit encoding : Yes
USSD use UCS-2 decoding : No
Tasks in queue : 0
Commands in queue : 0
Call Waiting : Disabled
Current device state : start
Desired device state : start
When change state : now
Calls/Channels : 0
Active : 0
Held : 0
Dialing : 0
Alerting : 0
Incoming : 0
Waiting : 0
Releasing : 0
Initializing : 0

raspbx*CLI> dongle show device settings dongle0
------------- Settings ------------
Device : dongle0
Audio : /dev/ttyUSB1
Data : /dev/ttyUSB2
IMEI :
IMSI :
Channel Language : en
Context : from-trunk-dongle
Exten : +1XXXXXXXXXX
Group : 0
RX gain : 0
TX gain : 0
U2Diag : -1
Use CallingPres : Yes
Default CallingPres : Presentation Allowed, Passed Screen
Auto delete SMS : Yes
Disable SMS : No
Reset Dongle : Yes
SMS PDU : Yes
Call Waiting : auto
DTMF : relax
Minimal DTMF Gap : 45
Minimal DTMF Duration : 80
Minimal DTMF Interval : 200
Initial device state : start

Inbound Routes name : inbound
DID Number?
inbound Set Destination : Extensions <200> 200-ext
Outbound Route name : out_GSM
Route CID:?
Dial Patterns that will use this Route : NXXNXXXXXX & NXXXXXX & X.
Trunk Sequence for Matched Routes 0 : Dongle (Unlocked huawei E303s-1)
Optional Destination on Congestion : Normal Congestion
Trunks Name : Dongle
Outbound Cellared:
Maximum Channels : 1
Custom Dial String : dongle/dongle0/$OUTNUM$

tried youtube aswell no luck so far almost 2 weeks of search for help find no detailed answer
anybody here able to give me better detailed setup for Raspbx GSM Gateway much appreciated

so far SMS(http://raspbx/SMS/) working as it is supposed to
any call come in to the SIM on the Dongle gateway answerable via PC based(sip) soft phone
NOW
I can make any call from PC based(sip) soft phone to any number via GSM Dongle
Once the PC based(sip) soft phone goes offline !? I want to make calls Both way
Incoming calls to GSM Dongle forward to my phone/s (sip setup ?)
outgoing calls (sip setup-sip setup?)through GSM Dongle
how can i set up that ?

in another word i guess i need freepbx setup guide
such as DISA + Ring Groups + Follow Me implication for my GSM Gateway
as i said above i have only,
1 extention also using with x-lite soft phone (Extensions <200>)
1 inbound route
1 outbound route
1 Trunk (Dongle)
anybody here able to give me better detailed setup for Raspbx GSM Gateway much appreciated

What do you see in the log when a call comes in?

i have attached a link http://pastebin.com/ekX7kM4w which i can update if any one needs more log details in the future