Outgoing and incoming not working in freepbx 2.11.0.37

i had newly installed asterisk 11 with freepbx 2.11 on new pc with dahdi driver install as we have sangoma a101 pci card .

but when i dial below error messg.
[[email protected] /]# asterisk -rvvvvvvvv
Asterisk 11.9.0, Copyright © 1999 - 2013 Digium, Inc. and others.
Created by Mark Spencer [email protected]
Asterisk comes with ABSOLUTELY NO WARRANTY; type ‘core show warranty’ for detail s.
This is free software, with components licensed under the GNU General Public
License version 2 and other licenses; you are welcome to redistribute it under
certain conditions. Type ‘core show license’ for details.

Connected to Asterisk 11.9.0 currently running on bridgesgi (pid = 26114)
== Using SIP RTP TOS bits 184
== Using SIP RTP CoS mark 5
– Executing [[email protected]:1] ResetCDR(“SIP/9802-0000000c”, “”) in new stack
– Executing [[email protected]:2] NoCDR(“SIP/9802-0000000c”, “”) in new stack
– Executing [[email protected]:3] Progress(“SIP/9802-0000000c”, “”) in new stack
– Executing [[email protected]:4] Wait(“SIP/9802-0000000c”, “1”) in new stack
> 0x7fa7640223f0 – Probation passed - setting RTP source address to 192.168.10.123:5004
– Executing [[email protected]:5] Progress(“SIP/9802-0000000c”, “”) in new stack
– Executing [[email protected]:6] Playback(“SIP/9802-0000000c”, “silence/1&cannot-complete-as-dialed&check-number-dial-again,noanswer”) in new stack
– <SIP/9802-0000000c> Playing ‘silence/1.gsm’ (language ‘en’)
– <SIP/9802-0000000c> Playing ‘cannot-complete-as-dialed.gsm’ (language ‘en’)
– <SIP/9802-0000000c> Playing ‘check-number-dial-again.gsm’ (language ‘en’)
– Executing [[email protected]:7] Wait(“SIP/9802-0000000c”, “1”) in new stack
– Executing [[email protected]:8] Congestion(“SIP/9802-0000000c”, “20”) in new stack
== Spawn extension (from-internal, 99900039877, 8) exited non-zero on ‘SIP/9802-0000000c’
– Executing [[email protected]:1] Hangup(“SIP/9802-0000000c”, “”) in new stack
== Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/9802-0000000c’
bridgesgi*CLI>

can anybody tell where is exact problem.

pci card details.
[[email protected] ~]# lspci
00:00.0 Host bridge: Intel Corporation 4th Gen Core Processor DRAM Controller (rev 06)
00:02.0 VGA compatible controller: Intel Corporation Device 041e (rev 06)
00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06)
00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 04)
00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
00:16.3 Serial controller: Intel Corporation 8 Series/C220 Series Chipset Family KT Controller (rev 04)
00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d4)
00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d4)
00:1c.3 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d4)
00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation B85 Express LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 04)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
03:00.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 41)
04:00.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card

Is the card configured.
Have you created an outbound route?

how to configure card and outbound route is set
9-0NXXXXXXXXXX
9-NXXXXXXX
9-XNXXXXXXXXXX