Hello. I am relatively new to Freepbx and Asterisk, but have been using standalone SIP trunks and both softphones (X-Lite) and CISCO 7940 SIP phones with Sipgate for about 5 years. I am using DD-WRT on my router with ports open and forwarded to my FreePBX / Asterisk Server on a Raspberry Pi using the latest install of IncrediblePBX (Asterisk 11.6.0 and FreePBX 2.11.0.23)
I have installed the Sipgate Trunk, set up incoming calls and outgoing calls including setting up UK dialplans with calls fowarded to an extension which is registered.
First the good things:
- The trunk is registered and online
- The extension is registered and online
- I can use the extension to dial out and to make calls, with two way audio
- I can dial in on a PSTN line and the call is answered by Asterisk, but is diverted to the extension’s voicemail if enabled, or returns a number unobtainable tone if voicemail is inactive on the extension
BUT despite trying a 101 things in the extension setting I cannot get incoming calls to ring and connect to the registered extension (for the time being I am using a softphone X-Lite to do the testing, but the same occurs on a 7940 if this is connected).
I wonder if anybody can help me please?
The following is the Log when an incoming call is received, anybody have any ideas as to what is going on please and how to fix this?
The only warnings I can see below are these two lines:
[2014-02-15 10:54:09] WARNING[5308][C-0000002a] chan_sip.c: Purely numeric hostname (705), and not a peer–rejecting!
[2014-02-15 10:54:09] WARNING[5308][C-0000002a] app_dial.c: Unable to create channel of type ‘SIP’ (cause 20 - Subscriber absent)
I have tried googling these errors, without much success.
Thanks in anticipation that this is an easy fix?
Andrew
The full Log extract follows:
[2014-02-15 10:54:09] VERBOSE[3027][C-0000002a] netsock2.c: == Using SIP RTP TOS bits 184
[2014-02-15 10:54:09] VERBOSE[3027][C-0000002a] netsock2.c: == Using SIP RTP CoS mark 5
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:1] Set(“SIP/sipgateUK1TR-00000038”, “__FROM_DID=1358481”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:2] Gosub(“SIP/sipgateUK1TR-00000038”, “app-blacklist-check,s,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:1] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?check-blocked”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:2] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?check-blocked”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:3] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?check-blocked:morechecks”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (app-blacklist-check,s,5)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:5] NoOp(“SIP/sipgateUK1TR-00000038”, “1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:6] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?strip2”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:7] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?strip1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:8] Goto(“SIP/sipgateUK1TR-00000038”, “check”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (app-blacklist-check,s,14)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:14] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?blacklisted”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:15] Set(“SIP/sipgateUK1TR-00000038”, “CALLED_BLACKLIST=1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@app-blacklist-check:16] Return(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:3] Set(“SIP/sipgateUK1TR-00000038”, “CDR(did)=1358481”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:4] ExecIf(“SIP/sipgateUK1TR-00000038”, “0 ?Set(CALLERID(name)=1518682)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:5] Ringing(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:6] Set(“SIP/sipgateUK1TR-00000038”, “__CALLINGPRES_SV=allowed_not_screened”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:7] Set(“SIP/sipgateUK1TR-00000038”, “CALLERPRES()=allowed_not_screened”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [1358481@from-trunk:8] Goto(“SIP/sipgateUK1TR-00000038”, “from-did-direct,705,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (from-did-direct,705,1)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [705@from-did-direct:1] Set(“SIP/sipgateUK1TR-00000038”, “__RINGTIMER=15”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [705@from-did-direct:2] Macro(“SIP/sipgateUK1TR-00000038”, “exten-vm,705,705,0,0,0”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:1] Macro(“SIP/sipgateUK1TR-00000038”, “user-callerid,”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:1] Set(“SIP/sipgateUK1TR-00000038”, “TOUCH_MONITOR=1392461649.56”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:2] Set(“SIP/sipgateUK1TR-00000038”, “AMPUSER=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:3] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?report”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:4] ExecIf(“SIP/sipgateUK1TR-00000038”, “1?Set(REALCALLERIDNUM=1518682)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:5] Set(“SIP/sipgateUK1TR-00000038”, “AMPUSER=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:6] Set(“SIP/sipgateUK1TR-00000038”, “AMPUSERCIDNAME=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:7] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?report”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-user-callerid,s,13)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:13] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?continue”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:14] Set(“SIP/sipgateUK1TR-00000038”, “__TTL=64”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:15] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?continue”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-user-callerid,s,26)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:26] Set(“SIP/sipgateUK1TR-00000038”, “CALLERID(number)=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:27] Set(“SIP/sipgateUK1TR-00000038”, “CALLERID(name)=02030518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:28] Set(“SIP/sipgateUK1TR-00000038”, “CDR(cnum)=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:29] Set(“SIP/sipgateUK1TR-00000038”, “CDR(cnam)=02030518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:30] Set(“SIP/sipgateUK1TR-00000038”, “CHANNEL(language)=en”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:2] Set(“SIP/sipgateUK1TR-00000038”, “RingGroupMethod=none”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:3] Set(“SIP/sipgateUK1TR-00000038”, “__EXTTOCALL=705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:4] Set(“SIP/sipgateUK1TR-00000038”, “__PICKUPMARK=705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:5] Set(“SIP/sipgateUK1TR-00000038”, “RT=15”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:6] Gosub(“SIP/sipgateUK1TR-00000038”, “sub-record-check,s,1(exten,705,)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:1] Set(“SIP/sipgateUK1TR-00000038”, “REC_POLICY_MODE_SAVE=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:2] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?check”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (sub-record-check,s,7)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:7] Set(“SIP/sipgateUK1TR-00000038”, “__MON_FMT=wav”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:8] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?next”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (sub-record-check,s,11)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:11] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Return()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:12] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(__REC_POLICY_MODE=)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:13] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?exten,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:14] Set(“SIP/sipgateUK1TR-00000038”, “__REC_STATUS=INITIALIZED”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:15] Set(“SIP/sipgateUK1TR-00000038”, “NOW=1392461649”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:16] Set(“SIP/sipgateUK1TR-00000038”, “__DAY=15”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:17] Set(“SIP/sipgateUK1TR-00000038”, “__MONTH=02”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:18] Set(“SIP/sipgateUK1TR-00000038”, “__YEAR=2014”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:19] Set(“SIP/sipgateUK1TR-00000038”, “__TIMESTR=20140215-105409”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:20] Set(“SIP/sipgateUK1TR-00000038”, “__FROMEXTEN=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:21] Set(“SIP/sipgateUK1TR-00000038”, “__CALLFILENAME=exten-705-1518682-20140215-105409-1392461649.56”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@sub-record-check:22] Goto(“SIP/sipgateUK1TR-00000038”, “exten,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (sub-record-check,exten,1)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exten@sub-record-check:1] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?callee”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exten@sub-record-check:2] Set(“SIP/sipgateUK1TR-00000038”, “__REC_POLICY_MODE=dontcare”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exten@sub-record-check:3] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?caller”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (sub-record-check,exten,10)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exten@sub-record-check:10] Set(“SIP/sipgateUK1TR-00000038”, “__REC_POLICY_MODE=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exten@sub-record-check:11] GosubIf(“SIP/sipgateUK1TR-00000038”, “0?record,1(exten,705,1518682)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exten@sub-record-check:12] Return(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:7] Macro(“SIP/sipgateUK1TR-00000038”, “dial-one,15,tr,705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:1] Set(“SIP/sipgateUK1TR-00000038”, “DEXTEN=705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:2] Set(“SIP/sipgateUK1TR-00000038”, “DIALSTATUS_CW=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:3] GosubIf(“SIP/sipgateUK1TR-00000038”, “0?screen,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:4] GosubIf(“SIP/sipgateUK1TR-00000038”, “0?cf,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:5] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?skip1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-dial-one,s,8)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:8] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?nodial”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:9] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?continue”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:10] Set(“SIP/sipgateUK1TR-00000038”, “EXTHASCW=ENABLED”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:11] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?next1:cwinusebusy”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-dial-one,s,23)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:23] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?next3:continue”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-dial-one,s,24)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:24] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(DIALSTATUS_CW=BUSY)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:25] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?nodial”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:26] GosubIf(“SIP/sipgateUK1TR-00000038”, “1?dstring,1():dlocal,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:1] Set(“SIP/sipgateUK1TR-00000038”, “DSTRING=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:2] Set(“SIP/sipgateUK1TR-00000038”, “DEVICES=705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:3] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Return()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:4] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(DEVICES=05)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:5] Set(“SIP/sipgateUK1TR-00000038”, “LOOPCNT=1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:6] Set(“SIP/sipgateUK1TR-00000038”, “ITER=1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:7] Set(“SIP/sipgateUK1TR-00000038”, “THISDIAL=SIP/705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:8] GosubIf(“SIP/sipgateUK1TR-00000038”, “1?zap2dahdi,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:1] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Return()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:2] Set(“SIP/sipgateUK1TR-00000038”, “NEWDIAL=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:3] Set(“SIP/sipgateUK1TR-00000038”, “LOOPCNT2=1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:4] Set(“SIP/sipgateUK1TR-00000038”, “ITER2=1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:5] Set(“SIP/sipgateUK1TR-00000038”, “THISPART2=SIP/705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:6] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(THISPART2=DAHDI/705)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:7] Set(“SIP/sipgateUK1TR-00000038”, “NEWDIAL=SIP/705&”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:8] Set(“SIP/sipgateUK1TR-00000038”, “ITER2=2”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:9] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?begin2”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:10] Set(“SIP/sipgateUK1TR-00000038”, “THISDIAL=SIP/705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [zap2dahdi@macro-dial-one:11] Return(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:9] Set(“SIP/sipgateUK1TR-00000038”, “DSTRING=SIP/705&”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:10] Set(“SIP/sipgateUK1TR-00000038”, “ITER=2”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:11] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?begin”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:12] Set(“SIP/sipgateUK1TR-00000038”, “DSTRING=SIP/705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [dstring@macro-dial-one:13] Return(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:27] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?nodial”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:28] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?skiptrace”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:29] GosubIf(“SIP/sipgateUK1TR-00000038”, “1?ctset,1():ctclear,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [ctset@macro-dial-one:1] Set(“SIP/sipgateUK1TR-00000038”, “DB(CALLTRACE/705)=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [ctset@macro-dial-one:2] Return(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:30] Set(“SIP/sipgateUK1TR-00000038”, “D_OPTIONS=tr”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:31] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?SIPAddHeader(Alert-Info: )”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:32] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?SIPAddHeader()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:33] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(CHANNEL(musicclass)=)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:34] GosubIf(“SIP/sipgateUK1TR-00000038”, “0?qwait,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:35] Set(“SIP/sipgateUK1TR-00000038”, “__CWIGNORE=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:36] Set(“SIP/sipgateUK1TR-00000038”, “__KEEPCID=TRUE”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:37] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?usegoto,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:38] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?godial”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-dial-one,s,42)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:42] Dial(“SIP/sipgateUK1TR-00000038”, “SIP/705,15,tr”) in new stack
[2014-02-15 10:54:09] WARNING[5308][C-0000002a] chan_sip.c: Purely numeric hostname (705), and not a peer–rejecting!
[2014-02-15 10:54:09] WARNING[5308][C-0000002a] app_dial.c: Unable to create channel of type ‘SIP’ (cause 20 - Subscriber absent)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] app_dial.c: == Everyone is busy/congested at this time (1:0/0/1)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:43] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?MacroExit()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:44] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(DIALSTATUS=)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:45] GosubIf(“SIP/sipgateUK1TR-00000038”, “0?s-CHANUNAVAIL,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-dial-one:46] MacroExit(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:8] Set(“SIP/sipgateUK1TR-00000038”, “SV_DIALSTATUS=CHANUNAVAIL”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:9] GosubIf(“SIP/sipgateUK1TR-00000038”, “0?docfu,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:10] GosubIf(“SIP/sipgateUK1TR-00000038”, “0?docfb,1()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:11] Set(“SIP/sipgateUK1TR-00000038”, “DIALSTATUS=CHANUNAVAIL”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:12] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?MacroExit()”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:13] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?s-CHANUNAVAIL,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-exten-vm:14] Macro(“SIP/sipgateUK1TR-00000038”, “vm,705,CHANUNAVAIL,”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-vm:1] Macro(“SIP/sipgateUK1TR-00000038”, “user-callerid,SKIPTTL”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:1] Set(“SIP/sipgateUK1TR-00000038”, “TOUCH_MONITOR=1392461649.56”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:2] Set(“SIP/sipgateUK1TR-00000038”, “AMPUSER=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:3] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?report”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:4] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(REALCALLERIDNUM=1518682)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:5] Set(“SIP/sipgateUK1TR-00000038”, “AMPUSER=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:6] Set(“SIP/sipgateUK1TR-00000038”, “AMPUSERCIDNAME=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:7] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?report”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-user-callerid,s,13)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:13] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?continue”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-user-callerid,s,26)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:26] Set(“SIP/sipgateUK1TR-00000038”, “CALLERID(number)=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:27] Set(“SIP/sipgateUK1TR-00000038”, “CALLERID(name)=02030518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:28] Set(“SIP/sipgateUK1TR-00000038”, “CDR(cnum)=1518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:29] Set(“SIP/sipgateUK1TR-00000038”, “CDR(cnam)=02030518682”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-user-callerid:30] Set(“SIP/sipgateUK1TR-00000038”, “CHANNEL(language)=en”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-vm:2] Set(“SIP/sipgateUK1TR-00000038”, “VMGAIN=g(6)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-vm:3] Macro(“SIP/sipgateUK1TR-00000038”, “blkvm-check,”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-blkvm-check:1] Set(“SIP/sipgateUK1TR-00000038”, “GOSUB_RETVAL=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-blkvm-check:2] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(GOSUB_RETVAL=TRUE)”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-blkvm-check:3] MacroExit(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-vm:4] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?vmx,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-vm,vmx,1)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:1] Set(“SIP/sipgateUK1TR-00000038”, “MEXTEN=705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:2] Set(“SIP/sipgateUK1TR-00000038”, “MMODE=CHANUNAVAIL”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:3] Set(“SIP/sipgateUK1TR-00000038”, “RETVM=”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:4] Set(“SIP/sipgateUK1TR-00000038”, “MODE=unavail”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:5] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?chknomsg”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-vm,vmx,7)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:7] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?s-CHANUNAVAIL,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:8] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?notdirect”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-vm,vmx,10)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:10] NoOp(“SIP/sipgateUK1TR-00000038”, "Checking if ext 705 is enabled: ") in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [vmx@macro-vm:11] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?s-CHANUNAVAIL,1”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-vm,s-CHANUNAVAIL,1)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s-CHANUNAVAIL@macro-vm:1] Macro(“SIP/sipgateUK1TR-00000038”, “get-vmcontext,705”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-get-vmcontext:1] Set(“SIP/sipgateUK1TR-00000038”, “VMCONTEXT=default”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-get-vmcontext:2] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?200:300”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-get-vmcontext,s,300)
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-get-vmcontext:300] NoOp(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:09] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s-CHANUNAVAIL@macro-vm:2] VoiceMail(“SIP/sipgateUK1TR-00000038”, “705@default,ug(6)”) in new stack
[2014-02-15 10:54:10] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘vm-theperson.ulaw’ (language ‘en’)
[2014-02-15 10:54:11] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘digits/7.ulaw’ (language ‘en’)
[2014-02-15 10:54:12] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘digits/0.ulaw’ (language ‘en’)
[2014-02-15 10:54:13] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘digits/5.ulaw’ (language ‘en’)
[2014-02-15 10:54:14] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘vm-isunavail.ulaw’ (language ‘en’)
[2014-02-15 10:54:15] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘vm-intro.ulaw’ (language ‘en’)
[2014-02-15 10:54:20] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘beep.ulaw’ (language ‘en’)
[2014-02-15 10:54:21] VERBOSE[5308][C-0000002a] app_voicemail.c: – Recording the message
[2014-02-15 10:54:21] VERBOSE[5308][C-0000002a] app.c: – x=0, open writing: /var/spool/asterisk/voicemail/default/705/tmp/iHiseV format: wav, 0x29782cc
[2014-02-15 10:54:21] VERBOSE[5308][C-0000002a] app.c: – x=1, open writing: /var/spool/asterisk/voicemail/default/705/tmp/iHiseV format: wav49, 0x2597d74
[2014-02-15 10:54:24] VERBOSE[5308][C-0000002a] app.c: – User ended message by pressing #
[2014-02-15 10:54:24] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘auth-thankyou.ulaw’ (language ‘en’)
[2014-02-15 10:54:25] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s-CHANUNAVAIL@macro-vm:3] Goto(“SIP/sipgateUK1TR-00000038”, “exit-SUCCESS,1”) in new stack
[2014-02-15 10:54:25] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-vm,exit-SUCCESS,1)
[2014-02-15 10:54:25] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exit-SUCCESS@macro-vm:1] GotoIf(“SIP/sipgateUK1TR-00000038”, “0?exit-RETURN,1”) in new stack
[2014-02-15 10:54:25] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exit-SUCCESS@macro-vm:2] Playback(“SIP/sipgateUK1TR-00000038”, “goodbye”) in new stack
[2014-02-15 10:54:25] VERBOSE[5308][C-0000002a] file.c: – <SIP/sipgateUK1TR-00000038> Playing ‘goodbye.ulaw’ (language ‘en’)
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: – Executing [exit-SUCCESS@macro-vm:3] Hangup(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] app_macro.c: == Spawn extension (macro-vm, exit-SUCCESS, 3) exited non-zero on ‘SIP/sipgateUK1TR-00000038’ in macro ‘vm’
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] app_macro.c: == Spawn extension (macro-exten-vm, s, 14) exited non-zero on ‘SIP/sipgateUK1TR-00000038’ in macro ‘exten-vm’
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: == Spawn extension (from-did-direct, 705, 2) exited non-zero on ‘SIP/sipgateUK1TR-00000038’
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: – Executing [h@from-did-direct:1] Macro(“SIP/sipgateUK1TR-00000038”, “hangupcall,”) in new stack
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-hangupcall:1] GotoIf(“SIP/sipgateUK1TR-00000038”, “1?theend”) in new stack
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: – Goto (macro-hangupcall,s,3)
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-hangupcall:3] ExecIf(“SIP/sipgateUK1TR-00000038”, “0?Set(CDR(recordingfile)=)”) in new stack
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: – Executing [s@macro-hangupcall:4] Hangup(“SIP/sipgateUK1TR-00000038”, “”) in new stack
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] app_macro.c: == Spawn extension (macro-hangupcall, s, 4) exited non-zero on ‘SIP/sipgateUK1TR-00000038’ in macro ‘hangupcall’
[2014-02-15 10:54:26] VERBOSE[5308][C-0000002a] pbx.c: == Spawn extension (from-did-direct, h, 1) exited non-zero on ‘SIP/sipgateUK1TR-00000038’